News Center
News Center
You Are Here:
Home
/
/
Industry News
Is the mud pump hydraulic stirring dredging pump installed on the excavator easy to use?
Is
The excavator hydraulic mud pump is a hydraulically driven mud pump that can be assembled on the excavator. It has automatic mixing function, does not require electricity, and is convenient to move. It has significant advantages in environmental protection dredging projects and solves the problem of low extraction concentration of traditional electric pumps. A series of difficult problems that cannot be overcome, such as limited use conditions, have attracted great attention in the domestic mud pump industry.
Product advantages of hydraulic mud pumps:
1. Safe and stable. Driven by a hydraulic system, no electricity is required, and there is no danger of leakage. Large bearing capacity, balanced transmission, and long component life;
2. Easy to use. It is directly installed at the front end of the excavating boom (replaces the original bucket), without the need to construct complex ground protection and fixing devices, and it is easier to manage.
3. Stable, efficient and wear-resistant. It has strong stability and high efficiency in long-term operation; the flow parts (pump body, page wheel, guard plate, stirring impeller, etc.) are made of high chromium wear-resistant alloy material, which effectively reduces the frequency of replacement of parts.
4. The concentration of granular fluid containing mud, silt, sludge, mortar, etc. can be extracted up to 50;
5. As an accessory of the excavator, when it is not conducive to direct digging, it can be extracted and transported over a long distance to improve the scope of application of the excavator and its own value.
Specific parameters:

Flow rate: 50m3/h-1000m3/h
Head: 5m-60m
Caliber: 50mm-300mm
Power: hydraulic
Matching equipment: excavator hydraulic station
Particles: ≤500mm
Material: high wear-resistant alloy (special requirements can be customized) +
What are the advantages of the excavator mud pump (hydraulic mud pump)? It is safer and more stable to drive by the hydraulic system. It does not require electricity, and can be applied to a variety of complex and harsh working conditions. Frequent transitions are required. The advantages are particularly obvious when the electric pump cannot be used. The bottom of the pump is equipped with a set of agitating impellers, which can directly spray the deposited sludge into turbulent flow. When encountering special working conditions, you can also choose to configure an auxiliary agitator or a high-pressure water gun on the outside of the pump body to improve the mixing efficiency. The flow part is made of high-strength wear-resistant alloy material casting, which has super wear resistance and large flow passages, which can efficiently transport slurry, silt, sludge, ore slurry, slag, coal slurry, and coal slurry containing larger solid particles. Medium such as sand and gravel.


Working conditions:
1. Driven by hydraulic station, the hydraulic motor used in this pump is suitable for small, medium and large hydraulic pump stations.
2. The excavator is hydraulically driven. This pump is suitable for Carter, Volvo, Komatsu, Hitachi, Sumitomo, Kobelco, Doosan, Hyundai, XCMG, Sany, Yuchai, Liugong, Longgong, Zhonglian, Shanzhong, Lin Excavators of various brands such as Gongong, Sunward, Xiagong, Jingong, etc.
As one of the few professional excavator hydraulic mud pump manufacturers in China, our factory has a complete range of product models, and the factory direct sales save all intermediate links, and the price is more affordable! Allow users to save purchase costs, obtain high-quality products and perfect services.


After-sales and warranty:
1. One year warranty / wooden box packaging, available in stock or customized, please inquire for details.
2. Technical standards, conditions and deadlines for the supplier to be responsible for quality: Three guarantees for quality.
3. Quality and technical standards: Manufactured in accordance with the national standard CJ/T standard, and the quality assurance system is implemented in accordance with ISO9001
4. During the warranty period; if the delivery medium meets the requirements of the pump's flow-through parts and can comply with the operating instructions, if the product is damaged due to poor manufacturing or cannot work normally, the factory will replace or repair it free of charge, and the vulnerable parts are not here. the term.
5. Our factory guarantees to provide customers with accessories for a long time.
Sixth, the factory provides comprehensive services for cooperative units.


Purpose of excavator mud pump:
1. Ports, rivers, lakes, etc. sand pumping, dredging, dredging, sand removal, etc.;
2. Extraction of mud, sand, gravel, etc., to reclaim the sea and build a port;
3. Slag discharge, slurry discharge and all solutions containing solid substances in iron ore, tailing ponds, concentrators and other mines;
4. Used in metallurgy, steel and other industries to absorb high-concentration tailings, waste slag, high-temperature iron slag, iron filings, etc.;
5. San
See more information
The excavator hydraulic mud pump is a hydraulically driven mud pump that can be assembled on the excavator. It has automatic mixing function, does not require electricity, and is convenient to move. It has significant advantages in environmental protection dredging projects and solves the problem of low extraction concentration of traditional electric pumps. A series of difficult problems that cannot be overcome, such as limited use conditions, have attracted great attention in the domestic mud pump industry.
Product advantages of hydraulic mud pumps:
1. Safe and stable. Driven by a hydraulic system, no electricity is required, and there is no danger of leakage. Large bearing capacity, balanced transmission, and long component life;
2. Easy to use. It is directly installed at the front end of the excavating boom (replaces the original bucket), without the need to construct complex ground protection and fixing devices, and it is easier to manage.
3. Stable, efficient and wear-resistant. It has strong stability and high efficiency in long-term operation; the flow parts (pump body, page wheel, guard plate, stirring impeller, etc.) are made of high chromium wear-resistant alloy material, which effectively reduces the frequency of replacement of parts.
4. The concentration of granular fluid containing mud, silt, sludge, mortar, etc. can be extracted up to 50;
5. As an accessory of the excavator, when it is not conducive to direct digging, it can be extracted and transported over a long distance to improve the scope of application of the excavator and its own value.
Specific parameters:

Flow rate: 50m3/h-1000m3/h
Head: 5m-60m
Caliber: 50mm-300mm
Power: hydraulic
Matching equipment: excavator hydraulic station
Particles: ≤500mm
Material: high wear-resistant alloy (special requirements can be customized) +
What are the advantages of the excavator mud pump (hydraulic mud pump)? It is safer and more stable to drive by the hydraulic system. It does not require electricity, and can be applied to a variety of complex and harsh working conditions. Frequent transitions are required. The advantages are particularly obvious when the electric pump cannot be used. The bottom of the pump is equipped with a set of agitating impellers, which can directly spray the deposited sludge into turbulent flow. When encountering special working conditions, you can also choose to configure an auxiliary agitator or a high-pressure water gun on the outside of the pump body to improve the mixing efficiency. The flow part is made of high-strength wear-resistant alloy material casting, which has super wear resistance and large flow passages, which can efficiently transport slurry, silt, sludge, ore slurry, slag, coal slurry, and coal slurry containing larger solid particles. Medium such as sand and gravel.


Working conditions:
1. Driven by hydraulic station, the hydraulic motor used in this pump is suitable for small, medium and large hydraulic pump stations.
2. The excavator is hydraulically driven. This pump is suitable for Carter, Volvo, Komatsu, Hitachi, Sumitomo, Kobelco, Doosan, Hyundai, XCMG, Sany, Yuchai, Liugong, Longgong, Zhonglian, Shanzhong, Lin Excavators of various brands such as Gongong, Sunward, Xiagong, Jingong, etc.
As one of the few professional excavator hydraulic mud pump manufacturers in China, our factory has a complete range of product models, and the factory direct sales save all intermediate links, and the price is more affordable! Allow users to save purchase costs, obtain high-quality products and perfect services.


After-sales and warranty:
1. One year warranty / wooden box packaging, available in stock or customized, please inquire for details.
2. Technical standards, conditions and deadlines for the supplier to be responsible for quality: Three guarantees for quality.
3. Quality and technical standards: Manufactured in accordance with the national standard CJ/T standard, and the quality assurance system is implemented in accordance with ISO9001
4. During the warranty period; if the delivery medium meets the requirements of the pump's flow-through parts and can comply with the operating instructions, if the product is damaged due to poor manufacturing or cannot work normally, the factory will replace or repair it free of charge, and the vulnerable parts are not here. the term.
5. Our factory guarantees to provide customers with accessories for a long time.
Sixth, the factory provides comprehensive services for cooperative units.


Purpose of excavator mud pump:
1. Ports, rivers, lakes, etc. sand pumping, dredging, dredging, sand removal, etc.;
2. Extraction of mud, sand, gravel, etc., to reclaim the sea and build a port;
3. Slag discharge, slurry discharge and all solutions containing solid substances in iron ore, tailing ponds, concentrators and other mines;
4. Used in metallurgy, steel and other industries to absorb high-concentration tailings, waste slag, high-temperature iron slag, iron filings, etc.;
5. San
Principle and use of regular hydraulic mud pump-excavator dredging pump
Principle
The regular hydraulic mud pump-excavator dredging pump is a submersible single-stage single-suction centrifugal pump, which is divided into several series and specifications such as 300mm, 250mm, 200mm, 150mm, 100mm, etc. according to the outlet diameter. The flow parts of the hydraulic mud pump are made of high chromium wear-resistant alloy materials. After a large number of tests and industrial field operation tests, the pump is wear-resistant, energy-saving, reliable in operation, high lift, and submersible (can be pumped to a depth of 60 meters) , Large flow (up to 1000 cubic meters per hour for a single pump), wide application range, long conveying distance, etc. The pumped solid-liquid mixed concentration can reach 60, which is suitable for pumping various mud, slag slurry, silt, ore, industrial and mining enterprises to transport slag, tailing slurry, tailings ore, slurry, power fly ash transportation and other highly abrasive media .
   

Main features of hydraulic slurry pump

1. There is a stirring impeller at the bottom of the pump, which can prevent large solid materials from blocking the pump, so that the solid and liquid are fully mixed, which is easier to handle.

2. This pump can handle solid materials with a particle size of 50mm, and the solid-liquid extraction concentration can reach more than 70;

Note: Due to different working conditions, the output of the pump may also vary with the influence of factors such as the processed medium, on-site operation, and transportation distance.

3. This device is mainly installed on the excavator. The power is provided by the hydraulic station of the excavator, which can realize free transition, and the power source is a diesel engine, which can solve the problem of power inconvenience during construction in remote areas.

4. The flow parts are made of hard chromium alloy, which has a long service life. The hydraulic drive of the dredging pump of the excavator has the following advantages:

1) Light weight per unit power, that is, under the condition of the same output power, it is small in size, light in weight, small inertia, compact in structure, and good in dynamic performance.

2) The hydraulic transmission device works smoothly, responds quickly, has little impact, and can quickly start, brake and change directions frequently. It is convenient to realize stepless speed regulation, and the speed regulation range is large.

3) Hydraulic transmission is easy to obtain large force and torque, which can make the transmission structure simple and low failure rate.

4) The control and adjustment of the hydraulic transmission device are relatively simple. It is more convenient, labor-saving, and easy to realize automation.

5) The hydraulic system is easy to achieve overload protection. At the same time, because the oil is used as the transmission medium, the relative moving surfaces can be lubricated by themselves, so the original parts have a long service life. Excavator dredging pump-dredging pump driven by excavator with hydraulic reamer

6) Since the hydraulic components have been standardized and generalized, the design, manufacture and use of the hydraulic system are more convenient. The arrangement of hydraulic components also has greater mobility.

Structural characteristics of excavator slurry pump

1. This pump is equipped with a stirring device, which can stir the sludge deposited on the bottom of the water into a turbulent flow and then extract it, instead of the traditional operation method with high-pressure water gun; excavator sludge pump

2. This pump is mainly composed of volute, impeller, pump seat, pump housing, stirring device, sealing device, motor seat, hydraulic motor, etc. The flow parts are made of high chromium wear-resistant alloy materials, which have a long service life;

The pump is fixed on the hydraulic excavator, and the power source comes from the hydraulic oil source of the excavator, avoiding the problem of having no power supply and additional power.

Precautions for use:

1. Ensure that the hydraulic oil of the system is pure, has less impurities, and has good lubricity, compatibility and stability;

2. According to the pressure, displacement, efficiency, etc. of the existing hydraulic system, a sediment pump should be reasonably equipped to enable the system to operate normally and not to exceed the system load for a long time;

3. When used with the excavator, the arm of the excavator should move lightly and slowly, and it is strictly forbidden to smash or smash it under hard working conditions to avoid damage to the pump body;

4. Select hydraulic oil pipes of standard specifications, use specified bolts and tighten them with torque. Unqualified installation will cause malfunction, damage or oil leakage;

5. When the equipment is transferred, it is necessary to ensure the cleanliness of the hydraulic oil port to prevent the entry of impurities, etc., which will affect the normal service life of the motor;

6.
See more information
The regular hydraulic mud pump-excavator dredging pump is a submersible single-stage single-suction centrifugal pump, which is divided into several series and specifications such as 300mm, 250mm, 200mm, 150mm, 100mm, etc. according to the outlet diameter. The flow parts of the hydraulic mud pump are made of high chromium wear-resistant alloy materials. After a large number of tests and industrial field operation tests, the pump is wear-resistant, energy-saving, reliable in operation, high lift, and submersible (can be pumped to a depth of 60 meters) , Large flow (up to 1000 cubic meters per hour for a single pump), wide application range, long conveying distance, etc. The pumped solid-liquid mixed concentration can reach 60, which is suitable for pumping various mud, slag slurry, silt, ore, industrial and mining enterprises to transport slag, tailing slurry, tailings ore, slurry, power fly ash transportation and other highly abrasive media .
   

Main features of hydraulic slurry pump

1. There is a stirring impeller at the bottom of the pump, which can prevent large solid materials from blocking the pump, so that the solid and liquid are fully mixed, which is easier to handle.

2. This pump can handle solid materials with a particle size of 50mm, and the solid-liquid extraction concentration can reach more than 70;

Note: Due to different working conditions, the output of the pump may also vary with the influence of factors such as the processed medium, on-site operation, and transportation distance.

3. This device is mainly installed on the excavator. The power is provided by the hydraulic station of the excavator, which can realize free transition, and the power source is a diesel engine, which can solve the problem of power inconvenience during construction in remote areas.

4. The flow parts are made of hard chromium alloy, which has a long service life. The hydraulic drive of the dredging pump of the excavator has the following advantages:

1) Light weight per unit power, that is, under the condition of the same output power, it is small in size, light in weight, small inertia, compact in structure, and good in dynamic performance.

2) The hydraulic transmission device works smoothly, responds quickly, has little impact, and can quickly start, brake and change directions frequently. It is convenient to realize stepless speed regulation, and the speed regulation range is large.

3) Hydraulic transmission is easy to obtain large force and torque, which can make the transmission structure simple and low failure rate.

4) The control and adjustment of the hydraulic transmission device are relatively simple. It is more convenient, labor-saving, and easy to realize automation.

5) The hydraulic system is easy to achieve overload protection. At the same time, because the oil is used as the transmission medium, the relative moving surfaces can be lubricated by themselves, so the original parts have a long service life. Excavator dredging pump-dredging pump driven by excavator with hydraulic reamer

6) Since the hydraulic components have been standardized and generalized, the design, manufacture and use of the hydraulic system are more convenient. The arrangement of hydraulic components also has greater mobility.

Structural characteristics of excavator slurry pump

1. This pump is equipped with a stirring device, which can stir the sludge deposited on the bottom of the water into a turbulent flow and then extract it, instead of the traditional operation method with high-pressure water gun; excavator sludge pump

2. This pump is mainly composed of volute, impeller, pump seat, pump housing, stirring device, sealing device, motor seat, hydraulic motor, etc. The flow parts are made of high chromium wear-resistant alloy materials, which have a long service life;

The pump is fixed on the hydraulic excavator, and the power source comes from the hydraulic oil source of the excavator, avoiding the problem of having no power supply and additional power.

Precautions for use:

1. Ensure that the hydraulic oil of the system is pure, has less impurities, and has good lubricity, compatibility and stability;

2. According to the pressure, displacement, efficiency, etc. of the existing hydraulic system, a sediment pump should be reasonably equipped to enable the system to operate normally and not to exceed the system load for a long time;

3. When used with the excavator, the arm of the excavator should move lightly and slowly, and it is strictly forbidden to smash or smash it under hard working conditions to avoid damage to the pump body;

4. Select hydraulic oil pipes of standard specifications, use specified bolts and tighten them with torque. Unqualified installation will cause malfunction, damage or oil leakage;

5. When the equipment is transferred, it is necessary to ensure the cleanliness of the hydraulic oil port to prevent the entry of impurities, etc., which will affect the normal service life of the motor;

6.
Urban water treatment is closely related to the urban environment
Urban
With the advancement of metropolis construction, more and more cities have gradually experienced drainage problems. When the rainy season occurs frequently, rainwater will be produced and cannot be discharged in time, causing waterlogging. Updating and expanding the drainage system and adding pumping stations has become a major issue in urban construction. The integrated pumping station will replace the traditional pumping station and become the main force in urban construction water treatment.


With the advancement of the city, more and more cities have gradually experienced drainage problems. The drainage system has been expanded and pumping stations have been added. Compared with traditional pumping stations, integrated pumping stations are more suitable for the needs of urban development.


The traditional pump room has a long construction period and requires a lot of manpower and material resources. When installing the integrated pumping station, the integrated pumping station highlights the advantages of small footprint, convenient installation and labor saving. In all conveniences, it is more economical than traditional pumping stations. The construction period is greatly shortened, and the efficiency is greatly improved compared with traditional pumping rooms.


The Flygt integrated pumping station has a professional monitoring platform, which can monitor the running status of the entire equipment at any time on a computer or mobile phone to ensure that the equipment is running without any worries.


Radisson (Beijing) Environmental Protection Technology Co., Ltd. has joined forces with Xylem of the United States and has been at the forefront of the world in the field of urban water treatment. Flygt TOP3 integrated pumping station and Flygt integrated pump gate are the best products in the industry and have multiple patented technologies. It can solve many problems in urban water treatment.
See more information
With the advancement of metropolis construction, more and more cities have gradually experienced drainage problems. When the rainy season occurs frequently, rainwater will be produced and cannot be discharged in time, causing waterlogging. Updating and expanding the drainage system and adding pumping stations has become a major issue in urban construction. The integrated pumping station will replace the traditional pumping station and become the main force in urban construction water treatment.


With the advancement of the city, more and more cities have gradually experienced drainage problems. The drainage system has been expanded and pumping stations have been added. Compared with traditional pumping stations, integrated pumping stations are more suitable for the needs of urban development.


The traditional pump room has a long construction period and requires a lot of manpower and material resources. When installing the integrated pumping station, the integrated pumping station highlights the advantages of small footprint, convenient installation and labor saving. In all conveniences, it is more economical than traditional pumping stations. The construction period is greatly shortened, and the efficiency is greatly improved compared with traditional pumping rooms.


The Flygt integrated pumping station has a professional monitoring platform, which can monitor the running status of the entire equipment at any time on a computer or mobile phone to ensure that the equipment is running without any worries.


Radisson (Beijing) Environmental Protection Technology Co., Ltd. has joined forces with Xylem of the United States and has been at the forefront of the world in the field of urban water treatment. Flygt TOP3 integrated pumping station and Flygt integrated pump gate are the best products in the industry and have multiple patented technologies. It can solve many problems in urban water treatment.
What are the advantages of an integrated pumping station
What
When installing the integrated pumping station, the area is small and the equipment is integrated into the prefabricated pumping station. The equipment is more intimate with the overall relationship, and it is more economical to build earthwork than to build a traditional pumping station.


The traditional pump house has a long construction period and requires a lot of manpower and material resources. The pumping station has been pre-installed and tested in the workshop, the construction period has been greatly reduced, and the results have been greatly improved compared with the traditional pumping station.


As the equipment meets, the comprehensive pumping stations are all installed together, and the construction site is quick and easy to build.


Xylem Feili top3 integrated pumping station has a professional monitoring platform, which can monitor the entire equipment on a computer or mobile phone to ensure no worries about operation.


The comprehensive prefabricated pumping station is mainly used for the network and discharge of wastewater from residential areas, workshops, schools, restaurants, hotels and other public places. Livelihood sewage, rural sewage, urban sewage treatment plants, rainwater networks and transportation in urban low-lying areas, reconstruction and expansion of old pumping stations, establishment and reform of urban sewage pipe networks; the circulation of lake water is inseparable from comprehensive prefabricated pumping stations.


At the same time, the comprehensive prefabricated pumping station is also used for sewage discharge in slaughterhouses, food processing plants, paper mills, and agriculture. Sewage discharge from highway work areas, stations, airports, large-scale construction sites and municipal reconstruction.


The comprehensive prefabricated component pumping station has the characteristics of efficient water supply and drainage, improved water level and flow, and maintaining the natural condition of the water body.


Comprehensive prefabricated pumping station is equipment for improving sewage, rainwater, drinking water and wastewater. It has the advantages of time saving, cost saving, convenient maintenance, low obstruction rate, fast installation, one-stop procurement, tailor-made, high-quality components, solid pumping station pipes, reliability and durability, condition detection and remote monitoring, etc. Strengths.


Radisson (Beijing) Environmental Protection Technology Co., Ltd. has joined forces with Xylem of the United States and has been at the forefront of the world in the field of urban water treatment. Flygt TOP3 integrated pumping station and Flygt integrated pump gate are the best products in the industry and have multiple patented technologies. It can solve many problems in urban water treatment.
See more information
When installing the integrated pumping station, the area is small and the equipment is integrated into the prefabricated pumping station. The equipment is more intimate with the overall relationship, and it is more economical to build earthwork than to build a traditional pumping station.


The traditional pump house has a long construction period and requires a lot of manpower and material resources. The pumping station has been pre-installed and tested in the workshop, the construction period has been greatly reduced, and the results have been greatly improved compared with the traditional pumping station.


As the equipment meets, the comprehensive pumping stations are all installed together, and the construction site is quick and easy to build.


Xylem Feili top3 integrated pumping station has a professional monitoring platform, which can monitor the entire equipment on a computer or mobile phone to ensure no worries about operation.


The comprehensive prefabricated pumping station is mainly used for the network and discharge of wastewater from residential areas, workshops, schools, restaurants, hotels and other public places. Livelihood sewage, rural sewage, urban sewage treatment plants, rainwater networks and transportation in urban low-lying areas, reconstruction and expansion of old pumping stations, establishment and reform of urban sewage pipe networks; the circulation of lake water is inseparable from comprehensive prefabricated pumping stations.


At the same time, the comprehensive prefabricated pumping station is also used for sewage discharge in slaughterhouses, food processing plants, paper mills, and agriculture. Sewage discharge from highway work areas, stations, airports, large-scale construction sites and municipal reconstruction.


The comprehensive prefabricated component pumping station has the characteristics of efficient water supply and drainage, improved water level and flow, and maintaining the natural condition of the water body.


Comprehensive prefabricated pumping station is equipment for improving sewage, rainwater, drinking water and wastewater. It has the advantages of time saving, cost saving, convenient maintenance, low obstruction rate, fast installation, one-stop procurement, tailor-made, high-quality components, solid pumping station pipes, reliability and durability, condition detection and remote monitoring, etc. Strengths.


Radisson (Beijing) Environmental Protection Technology Co., Ltd. has joined forces with Xylem of the United States and has been at the forefront of the world in the field of urban water treatment. Flygt TOP3 integrated pumping station and Flygt integrated pump gate are the best products in the industry and have multiple patented technologies. It can solve many problems in urban water treatment.
Mechanical seal leakage and solutions (1)-leakage of media
Mechanical
Mechanical seal leakage is sometimes related to the conveying medium of the corrosion-resistant pump. When the medium is strong in acidity or alkalinity or contains solid particles, it can also cause leakage.

(1) After most of the mechanical seals of submersible sewage pumps are disassembled, the auxiliary seals of the stationary ring and the moving ring are inelastic, and some have rotted, causing a large amount of leakage of the mechanical seal and even the phenomenon of shaft grinding. Due to the corrosive effect of high temperature, weak acid and weak alkali in the sewage on the static ring and the auxiliary rubber seal of the moving ring, the mechanical leakage is too large. The material of the moving and static ring rubber sealing ring is nitrile-40, which is not resistant to high temperature. It is not resistant to acid and alkali, and it is easy to corrode when the sewage is acid and alkali.

Countermeasures: For corrosive media, rubber parts should be fluorine rubber resistant to high temperature, weak acid and weak alkali.

(2) Mechanical seal leakage caused by solid particles and impurities If solid particles enter the end face of the seal, it will scratch or accelerate the wear of the end face. The accumulation of scale and oil on the shaft (sleeve) surface exceeds the wear rate of the friction pair, resulting in The moving ring cannot compensate for the wear displacement, and the operating life of the hard-to-hard friction pair is longer than that of the hard-to-graphite friction pair, because solid particles will be embedded in the sealing surface of the graphite sealing ring.

Countermeasures: The mechanical seal of tungsten carbide to tungsten carbide friction pair should be selected in the position where solid particles are easy to enter.

The corrosion-resistant pump manufacturer Keyikai focuses on the research and development and production of intelligent corrosion-resistant pumps, allowing the pump to work like a human, with zero cost maintenance. The company has many on-site installation engineers with 20 years of industry experience, free of charge for customers to answer on-site installation and maintenance problems.
See more information
Mechanical seal leakage is sometimes related to the conveying medium of the corrosion-resistant pump. When the medium is strong in acidity or alkalinity or contains solid particles, it can also cause leakage.

(1) After most of the mechanical seals of submersible sewage pumps are disassembled, the auxiliary seals of the stationary ring and the moving ring are inelastic, and some have rotted, causing a large amount of leakage of the mechanical seal and even the phenomenon of shaft grinding. Due to the corrosive effect of high temperature, weak acid and weak alkali in the sewage on the static ring and the auxiliary rubber seal of the moving ring, the mechanical leakage is too large. The material of the moving and static ring rubber sealing ring is nitrile-40, which is not resistant to high temperature. It is not resistant to acid and alkali, and it is easy to corrode when the sewage is acid and alkali.

Countermeasures: For corrosive media, rubber parts should be fluorine rubber resistant to high temperature, weak acid and weak alkali.

(2) Mechanical seal leakage caused by solid particles and impurities If solid particles enter the end face of the seal, it will scratch or accelerate the wear of the end face. The accumulation of scale and oil on the shaft (sleeve) surface exceeds the wear rate of the friction pair, resulting in The moving ring cannot compensate for the wear displacement, and the operating life of the hard-to-hard friction pair is longer than that of the hard-to-graphite friction pair, because solid particles will be embedded in the sealing surface of the graphite sealing ring.

Countermeasures: The mechanical seal of tungsten carbide to tungsten carbide friction pair should be selected in the position where solid particles are easy to enter.

The corrosion-resistant pump manufacturer Keyikai focuses on the research and development and production of intelligent corrosion-resistant pumps, allowing the pump to work like a human, with zero cost maintenance. The company has many on-site installation engineers with 20 years of industry experience, free of charge for customers to answer on-site installation and maintenance problems.
Previous page
1
2

底部-联系我们

Time of issue:2021-06-22 14:56:31

Hangzhou Xiaoshan Meite Light Industrial Machinery Co., Ltd.

Address: No. 265, kanshan Avenue, Guali Town, Hangzhou, Zhejiang
Tel: +86-571-82519727 / 83510265
Fax: +86-571-82519726
E-mail:mtqj@163.com

底部-版权信息

Time of issue:2021-06-22 15:32:07
Copyright © Hangzhou Xiaoshan Meite Light Industrial Machinery Co., Ltd. Powered by www.300.cn